COOLPIX S4100 固件

Instructions before updating your firmware

• This service provides software for upgrading COOLPIX S4100 firmware to Ver. 1.1 . Verify your camera’s firmware version from the Firmware version item in the setup menu. If the firmware version previously indicated is already installed in your camera, you need not update the firmware.

• Be sure to read the section below regarding modifications enabled with upgrade before upgrading the firmware.

• The camera may be damaged if power is interrupted or camera controls are operated during the update. Do not turn the camera off, remove or disconnect the power source, or operate camera controls during the update. If the update is not completed successfully and the camera becomes inoperable, take the camera to a Nikon-authorized service representative for inspection.
  
  If, for any reason, you are unsure on how to update your camera’s firmware yourself, please take your camera to an authorized Nikon service representative, where they will perform the update for you.

• When firmware is updated, images recorded to the camera’s internal memory are erased.
  Be sure to back up necessary images recorded to the camera’s internal memory to an SD memory card or computer before upgrading the firmware.

Modifications enabled with firmware Ver. 1.1

• When the Charging AC Adapter EH-69P and USB Cable UC-E6 were connected to the camera to charge the Rechargeable Li-ion Battery EN-EL19 with the EN-EL19 at or very near full exhaustion, the battery sometimes could not be charged. This issue has been resolved.?

1. Turn on the camera.
2. Tap the ▲ tab at the bottom of the monitor to display the setting controls and tap ?(setup).
3. Tap "Firmware version" in the ?(setup) menu.
4. The camera's firmware version will be displayed.?
5. Turn off the camera.

System Requirements

? Downloads and Instructions

?

• 此服務提供用于將COOLPIX S4100 固件更新到1.1版的軟件。在設置菜單的“固件版本”項中可確定您相機的固件版本。如果您相機中已經安裝上述固件版本,則不必進行此固件更新。

• 在更新固件前,請務必先閱讀以下有關通過更新所作修改的內容。

• 如果在更新期間切斷電源或操作相機控制鍵,可能會使相機損壞。請勿在更新期間關閉相機、拔下電源線或斷開電源,或操作相機控制鍵。如果未成功完成更新并且相機變得無法正常使用,請將相機送到尼康授權的服務代表處進行檢修。
  
  如果因?yàn)槿魏卧?您不確定如何自行更新相機固件,請將相機送到授權的尼康維修站,他們將可以為您進行更新。

• 更新固件后,記錄在相機內存中的影像將被擦除。
  在更新固件前,務必將記錄在相機內存中的所需影像備份到SD記憶卡或計算機。

?對固件1.1版所作的修改

• 當充電AC適配器EH-69P和USB線UC-E6連接到相機,對耗盡或接近耗盡的EN-EL19鋰電池進行充電時,有時電池?zé)o法充電。該問題已解決。?

1. 打開相機。
2. 輕觸屏幕底部的▲標簽顯示設定圖標,然后輕觸 (設定)。
3. 輕觸顯示 (設置)菜單中的“固件版本”,然后再輕觸將其選中。
4. 將會顯示相機的固件版本。
5. 關閉相機。

系統要求

? 下載和指導